Search:

Type: Posts; User: Pete Wass; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    17
    Views
    964

    Tight chamber

    I think this would not happen in your chambers Al.

    Pete
  2. Replies
    17
    Views
    964

    Thanks Dan

    Your advice is well received. I'll see what I can find.

    Pete
  3. Replies
    17
    Views
    964

    Ok

    The bolt extraction cams do not touch at any position of the bolt's rotation. I have to wait a second or two to be able to open the bolt after firing to open the bolt easily. The bolt functions fine...
  4. Replies
    17
    Views
    964

    Remington Bolt handle re-location

    I have a Stainless Steel Remington action with a SS bolt handle on it's bolt. There is zero primary extraction with this bolt, which isn't all that unusual, from what I have been reading. Is there...
  5. Replies
    16
    Views
    1,046

    This type of scoring device

    Changes Worst edge to center to center, by the way.

    Pete
  6. Replies
    16
    Views
    1,046

    Prolly

    Frank is a good guy, hell help ya.

    Pete
  7. Replies
    24
    Views
    2,028

    I think this community

    pretty much trusts each other. If someone gets taken, the information would be quickly spread. It is a sad state of affairs that there are scammers widely in our society who routinely make a living...
  8. Replies
    5
    Views
    1,543

    The IBS questions

    On their entry form asks for the Stocker, I believe. If that be the case, that might leave the Gunsmith to fitting the barrel and perhaps timing a trigger if needed. Guns are not that complex a...
  9. Replies
    29
    Views
    2,431

    As a test

    you might want to consider firing one without a bullet, that might allay some of the unknown and safety issues. Tie rhe gun down and light it with a string on the trigger. Before I knew much about...
  10. Replies
    29
    Views
    2,431

    Should be easy enough to try one

    Just make a bushing and try one. Should light it up I would think. When I use to shoot Hunter cartridges I had both small and large primer cases and could never see any difference in the way they...
  11. Replies
    18
    Views
    2,298

    Thats about

    $210. more than I paid for the last Winchesters I bought.

    Pete
  12. I didn't look at his bolt

    and wonder if it would matter to him. That rifle was and is competitive. Lee is Old School.

    Pete
  13. Replies
    15
    Views
    2,034

    How about a plumb bob and string?

    Can't get a line any straighter.

    Pete
  14. Last time I saw Lee Euber shoot

    he was still shooting his LV sleeved Remington :).

    Pete
  15. Replies
    12
    Views
    1,817

    Jerry Stiller

    Had a post up a few months ago about torque values for barrels and action screws and what he had learned about them over the years. I wrote them down somewhere but who knows where??? I do remember it...
  16. Replies
    21
    Views
    2,524

    Beggs the question:

    How many attempts do snipers get or how many misses can the make and not be discovered?

    Pete
  17. Replies
    130
    Views
    156,844

    Sticky: I had the good fortune

    Of visiting Flash and he giving me a tour of his shop. Gene Beggs took me there when I was out to visit him and shoot in his tunnel.

    Pete
  18. Replies
    5
    Views
    1,543

    This is what I do also

    I figure if one has a rifle that is shooting consistently it becomes about the barrel after that so Whomever chambers the next barrel gets to be named.

    Pete
  19. Replies
    21
    Views
    2,524

    No 6.5's

    Sorry, I couldn't resist. ;)

    Pete
  20. Replies
    21
    Views
    2,524

    In the "Sniper World"

    What are the folks who make those rifles doing? I am assuming to shoot at the distances they do at a human, they need to have some kind of reasonable accuracy and need to know, pretty much, where...
  21. I also like the idea

    of the shoulder of the barrel being at least the size of the action face. That makes absolute sense to me. certainly shouldn't hurt anything. I wanted to say that in my last post but my thoughts...
  22. Replies
    41
    Views
    4,990

    I'm still shootin

    I went back to CF Score shooting a couple of years ago. Different kinda folks in CF Score shooting. Much more laid back, smaller hat sizes, generally. I've known most of the folks for years and some...
  23. I like the idea of long tenons

    Is there a scientific formula that can be applied to such things as barrel tenons to give a definite answer as to what is the best length for any given diameter? One would think the Federal...
  24. Replies
    41
    Views
    4,990

    The changes:

    This was my 13th winter in Florida. The first year I came here there were 2 venues I could shoot IR 50/50 at each month and I didn't miss any of the matches. The winds of Manatee was the first one to...
  25. Great Video Al

    Verrrry Interesting!

    Pete
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4