Search:

Type: Posts; User: danyboy; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. I guess with all these comments about using...

    I guess with all these comments about using 105-107 gr bullets in a 1:10 twist 6BR, I’ll finish my batch of Sierra #1510 75gr. FBHP and work on my accuracy consistency a little more. Thanks to...
  2. I wouldn’t dare argue any of his opinions and...

    I wouldn’t dare argue any of his opinions and advices , he invented the 30BR caliber after all and I respect that.
  3. I always meant Benchrest accuracy.

    I always meant Benchrest accuracy.
  4. I appreciate that, I was just wondering why, in a...

    I appreciate that, I was just wondering why, in a hunting rifle .243 with a 1:9.25" twist, it did pretty good and since it's the same diameter, figured it might work in a 6BR.
  5. No Muzzle brakes allowed, weight of my rifle is...

    No Muzzle brakes allowed, weight of my rifle is 12.25 lbs. I always found Hollow Points to be more accurate than Full Metal Jackets.
  6. They are Sierra Matchking. Why is it not a good...

    They are Sierra Matchking. Why is it not a good idea ?
  7. 6BR, 1:10’’ twist, 107 gr. Bullets at 100 yards ?

    Due to actual bullet shortage, buddy has 6 boxes of Sierra Matchking 107gr. he’s selling. I compete at 100 yards only, I got a 1:10’’ twist. I have had good groups with 75 gr. FBHP bullets but...
  8. I was thinking of bumping the shoulder back...

    I was thinking of bumping the shoulder back .0015-.002" , and check the accuracy. Some benchrest competitor I met says he bumps .004" and I can see his accurate results but I'm not sure I can trust...
  9. Bump shoulder with Redding 30BR Body Die for 6 BR

    I got a Custom made 6BR Lee Collet die but no BodyDie for this caliber. Since I already have a Redding 30BR Body Die could I use it to bump the shoulder of my 6BR brass ?
  10. Replies
    68
    Views
    23,459

    About the hard bolt lift: solved the problem....

    About the hard bolt lift: solved the problem. Since I only have a low budget, I built a custom rifle on a Savage Action and after searching if other savage owners had run into this problem, I worked...
  11. Replies
    68
    Views
    23,459

    Al, I’m using a custom made Lee Collet Die and...

    Al,
    I’m using a custom made Lee Collet Die and a Redding Body Die(only every 3-4 firings for the Body Die).
  12. Replies
    68
    Views
    23,459

    Will never work. 45 acp is .4762, fired 30BR case...

    Will never work. 45 acp is .4762, fired 30BR case base is .470. Perfect size would be 8 x 75 rimmed or 9 x 63 or 9.3 x 74R or 9.5 x57 Mannlicher Schoenaver which all are .4685. Got none of them but...
  13. Replies
    68
    Views
    23,459

    Good idea, got one, tried it out never worked....

    Good idea, got one, tried it out never worked. Fired case base is .470, 45 ACP die is .4762. Too big.
    Thanks anyway.
  14. Replies
    68
    Views
    23,459

    Hard bolt lift now

    Spent time reading about hard bolt lift on this forum. Something new to me came up : ring dies . With my 6 BR and it’s Custom made Lee Collet Die, I never experienced hard bolt lifts till about after...
  15. Replies
    43
    Views
    14,744

    Case length plug

    [QUOTE=Al Nyhus;835615]Amen! :cool: I have a bunch of case length plugs made from 12L14. -Al[/QUOTE
    PM sent to you.
  16. Replies
    68
    Views
    23,459

    results in fireforming from 6BR Lapua Brass to 30BR directly in 30BR chamber

    I thought I would post results of my fireforming experiment. Measured chamber length and trimmed back new Lapua 6BR brass enought to avoid brass neck dammage to chamber when fireforming. Loaded...
  17. Replies
    68
    Views
    23,459

    You were wright, don't know where I got this...

    You were wright, don't know where I got this .020" thickness issue. Thickness is around .012"
  18. Replies
    68
    Views
    23,459

    finally got my chamber length

    Russ,
    When you say 'Have fun with your 30BR', I sure have some just learning this bras forming stuff. I measured the chamber length: 1.525", which corresponds to one of the 3 reamer prints Dave...
  19. Replies
    68
    Views
    23,459

    I asked, little while back, whoever was supposed...

    I asked, little while back, whoever was supposed to have chambered this Shillen prefit barrel if there was a print of the reamer used. Dave Kiff gave Pacific Tool 3 'possible' prints of reamers that...
  20. Replies
    68
    Views
    23,459

    .

    .
  21. Replies
    68
    Views
    23,459

    OK, I thought you were pulling my leg. Sorry man....

    OK, I thought you were pulling my leg. Sorry man.
    I got some play dough . I'll give her a try, even in my good benchrest barrel. I imagine I'll have to trim new 6BR brass length wiase down to 1.5"...
  22. Replies
    68
    Views
    23,459

    Very funny

    Very funny
  23. Replies
    68
    Views
    23,459

    You shot a 6mm bullet in a .308" barrel ? No...

    You shot a 6mm bullet in a .308" barrel ? No dammage to the barrel ?
  24. Replies
    68
    Views
    23,459

    I appreciate the helpfull info . Thanks, danyboy

    I appreciate the helpfull info .
    Thanks,
    danyboy
  25. Replies
    68
    Views
    23,459

    Larry, Sorry for digging out such an old topic...

    Larry,
    Sorry for digging out such an old topic but when you say 'make sure you trim the cases first', do you mean length wise or neck thickness wise ?
    Thanks,
    danyboy
Results 1 to 25 of 60
Page 1 of 3 1 2 3