Search:

Type: Posts; User: dokey; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.11 seconds.

  1. Replies
    4
    Views
    1,501

    22-243 rifle twist

    What is the ideal twist for a 22-243 Wildcat with a 28" barrel?
  2. Replies
    1
    Views
    1,065

    Cutting a ball end mill shank

    I just acquired a couple of Ball end mills, one is 1-1/4", the other is 1". I need the shanks reduced to 3/4". I use DCMT 32.52 inserts and want to know what carbide hardness to look for. The mills...
  3. Replies
    1
    Views
    1,865

    Sweedish 38 mauser bolt

    I'd like to know what's involved in converting the Mauser 38 bolt from cocking on closing to cocking on opening
  4. Replies
    13
    Views
    4,217

    To protect a barrel I wrap a piece of brass or...

    To protect a barrel I wrap a piece of brass or aluminum around the end of the barrel when chucking it in the lathe
  5. Replies
    15
    Views
    4,331

    crowning

    I have a lathe and have crowned barrels on it. In this case the barrels are already crowned and all I want to do is put a 11* bevel just slightly larger than the bore. If you guys think it should be...
  6. Replies
    15
    Views
    4,331

    Cutting 11* crown advise on 22rf target barrels

    I just bought a 11* muzzle crowning tool with a brass pilot from Brownells. I tried crowning a 22rf barrel by hand using light pressure . The result wasn't smooth, it looked like a fine chatter. The...
  7. Replies
    1
    Views
    1,430

    Canjar M70-2B trigger

    What version Winchester 70 will a Canjar M70-2B trigger fit. I'm looking for one for pre 64 70
  8. Replies
    23
    Views
    34,913

    Anschutz 54 super match

    What barrel would fit an early Anschutz 54 Super Match? Are all 54 barrels interchangeable?
  9. Thread: Freeland Stocks

    by dokey
    Replies
    7
    Views
    6,636

    [QUOTE=Larry Wilkins;703164]Al Freeland and Sam...

    [QUOTE=Larry Wilkins;703164]Al Freeland and Sam Bond both used Weldwood Rescorena glue ( a red water based resin glue of the 50s)

    Cheers[/QUOT E]
    Weldwood rescorcinal resin is not water based...
  10. Replies
    7
    Views
    7,036

    micro motion trigger

    The creep can be adjusted by the sear engagement screw and the trigger movement after firing can be adjusted by the overtravel screw
  11. Replies
    0
    Views
    1,245

    electric checkering set on GB

    There's a DemBart electric checkering set listed on GB auction 594 192 474
  12. Replies
    1
    Views
    1,571

    barrel roll marking die

    how do you set up and use a barrel roll marking die
  13. Replies
    2
    Views
    1,795

    Allen Bradley VFD

    I'm looking at an Allen Bradley Powerflex 4M VFD model 22F-B012N103 for my Harrison 3 HP lathe. Anyone know anything about them?
  14. Replies
    6
    Views
    3,480

    Did it with carbide inserts, am amazed how well...

    Did it with carbide inserts, am amazed how well Delrin machines
  15. Replies
    6
    Views
    3,480

    Best method for turning Delrin

    I plan on making a couple of barrel spinners using 1" round Delrin stock and want some opinions on what tooling to use
  16. Thread: 5-C collet chuck

    by dokey
    Replies
    7
    Views
    3,501

    5-C collet chuck

    I need opinions on this 5C collet chuck listed on Ebay auction 2716 6755 4173. Need opinions how how these type Collet holders compare to the Drawbar types. I don't intend to do production work
  17. Replies
    18
    Views
    6,045

    I want to match the Win sporter crown. I think...

    I want to match the Win sporter crown. I think some of the replies will help
  18. Replies
    18
    Views
    6,045

    Cutting muzzle crown on 22 sporter

    What would be the best way to crown the muzzle on a 22rf sporter such as a Win 52 69 or 75 which is rounded?
  19. Replies
    7
    Views
    4,647

    Harrison M300 Drawbar

    I'm looking for a Drawbar and 5C collets for my Harrison M300 lathe. Aside from Harrison are there any other make of drawbar that will work?
  20. Thread: carbide inserts

    by dokey
    Replies
    17
    Views
    6,738

    I sent him an email and am waiting for a reply if...

    I sent him an email and am waiting for a reply if he has inserts to fit my DCMT holders
  21. Thread: carbide inserts

    by dokey
    Replies
    17
    Views
    6,738

    I tried looking up Cobalt inserts and couldn't...

    I tried looking up Cobalt inserts and couldn't find any info. My holders are DCMT
  22. Thread: carbide inserts

    by dokey
    Replies
    17
    Views
    6,738

    carbide inserts

    What would be the best carbide inserts and techniques for tapering barrels to a sporter contour on a Harrison M300 Lathe
  23. Replies
    24
    Views
    16,154

    Could you recommend one? I've been watching some...

    Could you recommend one? I've been watching some from China on Ebay and am curious if they're any good. I need one for 3 PH 3 HP 220V single phase input. How about the Teco L510-203-H1N?
    Pete
  24. Replies
    8
    Views
    5,154

    Quick change post for Harrison M300 lathe

    Is there a quick change tool post holder that will fit a Harrison M300 lathe?
  25. Replies
    8
    Views
    4,496

    Look up Loctite 420, it's used for prepositioned...

    Look up Loctite 420, it's used for prepositioned metal parts and is thinner than water
Results 1 to 25 of 61
Page 1 of 3 1 2 3