Search:

Type: Posts; User: SET; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    10
    Views
    2,398

    You would be much better off using a 6br or 6bra...

    You would be much better off using a 6br or 6bra for regular 500 yard matches.
  2. Replies
    10
    Views
    2,398

    On an overcast day with virtually no wind you may...

    On an overcast day with virtually no wind you may be able to get a 1/2 MOA or smaller group.

    Depends on your definition of "Accuracy".
  3. Replies
    19
    Views
    4,370

    It's been well over twenty years but I can still...

    It's been well over twenty years but I can still see her smile.
    I'm very sorry, Dick.
  4. Replies
    4
    Views
    5,095

    Take the forend off and there will be a spring...

    Take the forend off and there will be a spring loaded extractor strut on the left side. Put a clockwise turn or two with a hex wrench to increase the extractor pressure.
  5. Replies
    7
    Views
    4,543

    18 tpi.

    18 tpi.
  6. Replies
    7
    Views
    4,543

    This answer was given a while back to the same...

    This answer was given a while back to the same question.


    "DGA with a flat bolt nose. Receiver face to front of bolt = 0.750 inches so the tenon length should be 0.742 - 0.745 inches if you...
  7. Replies
    23
    Views
    10,332

    Okay, I'm by no means passing judgement, but I'm...

    Okay, I'm by no means passing judgement, but I'm having a little trouble visualizing your setup. I was under the impression that those little lathes had a .750 spindle bore, at the most. So...
  8. Replies
    5
    Views
    3,274

    I have yet to chamber a barrel where there was...

    I have yet to chamber a barrel where there was absolutely no O.D. run-out on the muzzle end once the breech end of the bore was dialed in true.
  9. Replies
    4
    Views
    2,946

    After bedding, lightly sand the Devcon with 400...

    After bedding, lightly sand the Devcon with 400 grit, then clean it completely along with the action.
    Been gluing with J-B that way for years without a failure.
  10. Replies
    3
    Views
    1,696

    This is what you probably saw although it seems...

    This is what you probably saw although it seems easy enough to make your own.
    ...
  11. if you look again, when the vid reaches the 25...

    if you look again, when the vid reaches the 25 second mark you can easily see the Buck "Adjust-tru" chuck.
  12. Thread: Panda vs Teddy

    by SET
    Replies
    31
    Views
    14,633

    It's over 150 but just under 160.

    It's over 150 but just under 160.
  13. Thread: Panda vs Teddy

    by SET
    Replies
    31
    Views
    14,633

    Mine is #941XX.

    Mine is #941XX.
  14. Thread: fireforming necks

    by SET
    Replies
    4
    Views
    1,744

    Why not just run the case up on a 7mm mandrel?...

    Why not just run the case up on a 7mm mandrel? Then use 7mm bullets to fire-form to your chamber.
  15. Replies
    32
    Views
    16,760

    You don't really need indexable tooling at all....

    You don't really need indexable tooling at all. You mentioned that you have HHS bits so just use those.
    You can grind them yourself for any procedure you do when chambering a barrel. Leaves a real...
  16. Replies
    1
    Views
    1,363

    Los Angeles area benchrest?

    I have a friend whose son is getting started in rifle shooting. He lives in the L.A. area so I suggested he join a range where they shoot some BR, whether it be centerfire or rimfire.
    Hopefully...
  17. Thread: COLLET numbers

    by SET
    Replies
    8
    Views
    3,221

    This may help.

    This may help.
  18. Thread: Dave Dohrmann

    by SET
    Replies
    20
    Views
    8,661

    Dave Dohrmann

    It saddens me to post this, but Dave Dohrmann passed away yesterday, Sunday April 4th.
    I considerd Dave a very close friend for many years as did many of you.

    His brother truely appreciates all...
  19. Thread: Stock Tape

    by SET
    Replies
    16
    Views
    5,093

    http://www.tru-kote.com/ He has some new...

    http://www.tru-kote.com/

    He has some new transparent tape that works very well.
  20. The jaws protrude through the webbing. It comes...

    The jaws protrude through the webbing. It comes in handy for those short parts that need to be turned. The photos are self explanatory.
  21. The manufacturer states it best. # The Royal...

    The manufacturer states it best.

    # The Royal Chuck Stop provides a simple, consistent method for locating short parts in a 3-jaw lathe chuck.
    # Captive, web-shaped design eliminates the danger of...
  22. Actually, we have always referred to these as...

    Actually, we have always referred to these as "spiders".
  23. Replies
    2
    Views
    1,381

    Actually, there is a photo of their rear rest...

    Actually, there is a photo of their rear rest here.
    http://www.benchrest.com/timeprecision/New_.22_RF_BR/new_.22_rf_br.html
  24. Thread: rifle rest

    by SET
    Replies
    5
    Views
    2,972

    http://www.baercustomrifles.com/ Click on...

    http://www.baercustomrifles.com/

    Click on the left side "Rest Systems".
  25. Thread: Dave Dohrmann

    by SET
    Replies
    7
    Views
    2,701

    Just give him a call. If he's not playing golf...

    Just give him a call. If he's not playing golf he'll answer.:eek:
    (864) 884-0155
Results 1 to 25 of 26
Page 1 of 2 1 2